IS 13065 : 1991 Bulk handling equipment - Wagon marshalling equipment - Endless rope type - General requirements
1 Scope
1.1 This Indian Standard covers general requirements ofendless/open rope type wagon marshaling equipment.
2 References
List of Indian Standards Relevant to Wagon Marshalling Equipment
IS 210 :1978Grey iron castings
IS 226 :1975Structural steel (standard quality)
IS 325 :1978Three phase induction motors
IS808Dimensions for hot-rolled steel sections
IS 808 : Part 1 : 1978 MB series (beams)
IS 808 : Part 2 : 1978 Columns - SCseries
IS 808 : Part 3 : 1979 Channel, MC andMCP series
IS 808 : Part 5 : 1976 Equal leg angles
IS 808 : Part 6 : 1976 Unequal legangles
IS 961 :1975Structural steel (high tensile)
IS 1030 :1982Carbon steel castings for general engineeringpurposes
IS1367 Technical supply conditionsfor threaded steelfasteners
IS 1367 : Part 1 :1980 Introduction and general information
IS 1367 : Part 2 :1979 Product grades and tolerances
IS 1367 : Part 3 :1979 Mechanical properties and testmethods forbolts, screws and studs with full loadability
IS 1367 : Part 5 :1980 Mechanical properties and testmethods for setscrews and similar threaded fasteners notunder tensile stress
IS 1367 : Part 6 :1980 Mechanical properties and testmethods for nutwith specified proof loads
IS 1367 : Part 7 :1980 Mechanical properties and testmethods for nutswithout specified proof loads
IS 1367 : Part 9 : 1979 Surfacediscontinuities on bolts, screws andstuds
IS 1367 : Part 10 :1979 Surface discontinuities on nuts
IS 1367 : Part 12 :1981 Phosphate coatings on threaded fasteners
IS 1367 : Part 13 :1983 Hot-dip galvanized coatings on threadedfasteners
IS 1367 : Part 14 :1984 Stainless steel threaded fasteners
IS 1367 : Part 16 :1979 Designation system and symbols
IS 1367 : Part 18 :1979 Marking and mode of delivery
IS 1387 :1967General requirements for supply ofmetallurgical materials
IS 1570 :1961Schedules for wrought steels for generalengineering purposes
IS 1570 : Part 1 :1978 Steel specified by tensile and/oryieldproperties
IS 1570 : Part 2 :1979 Carbon steels (unalloyed steels)
IS 1570 : Part 3 :1979 Carbon and carbon- manganese freecuttingsteels
IS 1570 : Part 5 :1972 Stainless and heat-resisting steels
IS 1856 :1977Steel wire ropes for haulage purposes in mines
IS 1865 :1974Iron castings with spheroidal or modulargraphite
IS 1875 :1978Carbon steel billets, blooms, slabs and barsfor forgings
IS 2004 :1978 Carbon steel forgings forgeneral engineeringpurposes
IS 2048 :1983Parallel keys and keyways
IS 2062 :1984Weldable structural steel
IS 2107 :1977Whiteheart malleable iron casting
IS 2108 :1977Blackheart malleable iron casting for generalengineering purposes
IS 2291 :1981Tangential keys and keyways
IS 2292 :1974Taper keys and keyways
IS 2293 :1974Gib-head keys and keyways
IS 2294 :1980Woodruff keys and keyways
IS 2327 :1963Dimensions for straight sides splines forgeneral engineering use
IS 2708 :19841.5 percent manganese steel casting for generalengineering purposes
IS 3654 :1966Dimensions for straight sides serrations
IS 3665 :1966Dimensions for involute sided splines
IS 3973 :1967Code of practices for the selection,installation and maintenance of wire ropes
IS4218ISO metric screw threads
IS 4218 : Part 1 :1976 Basic and design profiles
IS 4218 : Part 2 :1976 Diameter pitch combinations
IS 4218 : Part 3 :1976 Basic dimensions for design profiles
IS 4218 : Part 4 :1976 Tolerancing system
IS 4218 : Part 5 :1979 Tolerances
IS 4218 : Part 6 :1978 Limits of sizes for commercial boltsand nuts (diameter range 1 to 52 mm)
IS 7403 :1974Code of practice for selection of standard wormand helical gear boxes