IS 13082 : Part 1 : 1991 Bulk handling equipment - Ship unloader - Gantry mounted grab type - Code of practice for design, manufacture and erection: Part 1 Mechanical and structural requirements

1 Scope

This Standard covers mechanical, structural, inspection andtesting requirements relating to the design, manufacture, anderection of gantry mounted grab type ship unloader provided withhorizontal boom and grab-bucket.

2 References

List of Referred Indian Standards

IS 210 :1978Grey iron castings

IS 919 : Part 1 :1963 Recommendations for limits and fitsforengineering:Part 1 General engineering

IS 1136 :1958Preferred, sizes for wrought metal products

IS 1364 : Part 1 :1983 Hexagon head bolts, screws and nuts ofproductsgrades C: Part 1 Hexagon head bolts(size range M5 to M36)

Part 2 :1984Part 2 Hexagon head screws (size range M5 toM36)

Part 3 :1984Part 3 Hexagon nuts (size range M5 to M36

Part 4 :1985Part 4 Hexagon thin nuts (chamfered) (size rangeM1.6 to M36)

Part 5 :1985Part 5 Hexagon thin nuts (unchamfered) (sizerange M1.6 to M10)

IS 1367 : Part 1 :1980 Technical supply conditions for threadedsteelfasteners:Part 1 Introduction and general information

Part 2 :1979Part 2 Product grades and tolerances

Part 3 :1979Part 3 Mechanical properties and test methodsfor bolts, screws and studs with fullloadability

Part 5 :1980Part 5 Mechanical properties and test methodsfor set screws and similar threaded fasteners not under tensile stresses

Part 6 :1980Part 6 Mechanical properties and test methodsfor nuts with specified proof loads

Part 7 :1980Part 7 Mechanical properties and test methodsfor nuts without specified proof loads

Part 9 :1979Part 9 Surface discontinuities on bolts, screwsand studs

Part 10 :1979Part 10 Surface discontinuities on nuts

Part 12 :1979Part 12 Phosphate coatings on threaded fasteners

Part 13 :1979Part 13 Hot-dip galvanized coatings on threadedfasteners

Part 14 :1984Part 14 Stainless steel threaded fasteners

Part 16 :1979Part 16 Designation system and symbols

Part 18 :1979Part 18 Marking and mode of delivery

IS 2016 :1967Plain washers

IS 2048 :1983Parrellel keys and keyways

IS 2266 :1977Steel wire ropes for general engineeringpurposes

IS 2291 :1981Tangential keys and keyways

IS 2292 :1974Taper keys and keyways

IS 2293 :1974Gib-head keys and keyways

IS 2294 :1986Woodruff keys and keyways

IS 2327 :1963Dimensions for straight sided splines forgeneral engineering use

IS 3177 :1977Code of practice for overhead traveling cranesand gantry cranes other than steel works cranes

IS 3665 :1966Dimensions for involute sided splines

IS 4009 : Part 1 :1981 Grease nipples:Part 1 Button head grease nipples

Part 2 :1981Part 2 Conical head grease nipples

IS 4672 :1982Grease cups

IS 4673 :1968Wick feed Lubricators

IS 5019 :1968Lubricating plugs

IS 5372 :1975Taper washers for channels (ISMC)

IS 5374 :1975Taper washers for I-beams (ISMB)

IS 5548 :1970Lubricating nipple adaptors

IS 5664 :1984Lubricating connectors

IS 6166 :1971Thin taper keys and keyways

IS 6167 :1971Thin parallel keys and keyways

IS 7745 :1975Dimensions of lubrication holes, grooves andbore relief

IS8593Recommendations for centralised lubrication asapplied to plant and machinery

Part 1 :1977Part 1 Oil lubrication

Part 2 :1988Part 2 Grease lubrication system

Part 3 :1984Part 3 Aerosol lubrication

IS 13148 :1991Bulk handling equipment-mobile continuous type -Rules for design of structures