IS 15630 : 2005 /ISO 7435 : 1983 Slotted Set Screws with Long Dog Point

ICS 21.060.10 PGD 37
Reaffirmed 2021

National Foreword

This Indian Standard which is identical with ISO 7435 : 1983 ?Slotted set screws with long dog. point? issued by the International Organization for Standardization ( ISO ) was adopted by the Bureau of Indian Standards on the recommendations of the Bolts, Nuts and Fasteners Accessories Sectional Committee and approval of the Medical Instruments, General and Production Engineering Division Council.

The other standards in this series are given below:

IS 15628 : 2005 Slotted set screws with flat point

IS 15629 : 2005 Slotted set screws with cone point

IS 15631 : 2005 Slotted set screws with cup point

Earlier the above subjects were movered by IS 2388 : 1971 ?Slotted grub screws ( first revision)? and the sizes were covered from M 1 to M 24 whereas this draft covers the sizes from M 1.2 to M 12. The Committee responsible for formulation of these standards decided that after the publication of above standards, IS 2388 : 1971 which earlier covered the above subjects, shall be withdrawn.

The text of ISO Standard has been approved as suitable for publication as an Indian Standard without deviations. Certain terminology and conventions are, however, not identical to those used in Indian Standards. Attention is particularly drawn to the following:

a) Wherever the words ?International Standard? appear, referring to this standard, they should be read as ?Indian Standard?.

b) Comma ( , ) has been used as a decimal marker while in Indian Standards, the current practice is to use a point ( . ) as the decimal marker.

In this adopted standard, reference appears to certain International Standards for which Indian Standards also exist. The corresponding Indian Standards, which are to be substituted in their places, are listed below along with their degree of equivalence for the editions indicated:

     International Standard      Corresponding Indian Standard
ISO 225 : 1983 IS 8536 : 1987 Fasteners - Bolts,
screws, studs and nuts - Symbols
and designations of dimensions ( first
revision )
ISO 261 : 1998 IS 4218 ( Part 2 ) : 2001 ISO general
purpose metric screw threads:
Part 2 General plan ( second revision)
ISO 888 : 1976 IS 4206 : 1987 Dimensions for nominal
lengths and thread lengths for bolts,
screws and studs ( first revision )
ISO 898-5 : 1998 IS 1367 (Part 5) : 2002 Technical
supply conditions for threaded steel
fasteners: Part 5 Mechanical
properties of fasteners made of
carbon steel and alloy steel - Set
screws and similar threaded
fasteners not under tensile stresses
( third revision)
ISO 965-1 : 1998 IS 14962 ( Part 1 ) : 2001 ISO general
purpose metric screw threads -
Tolerances: Part 1 Principles and
basic data
ISO 965-2 : 1998 IS 14962 ( Part 2 ) : 2001 ISO general
purpose metric screw threads -
Tolerances: Part 2 Limits of sizes
for general purpose external and
internal screw threads - Medium
quality
ISO 965-3 : 1998 IS 14962 ( Part 3 ) : 2001 ISO general
purpose metric screw threads -
Tolerances: Part 3 Deviations for
constructional screw threads
ISO 3269 : 1988 IS 1367 ( Part 17 ) : 2004 Technical
supply conditions for threaded steel
fasteners: Part 17 Inspection,
sampling and acceptance procedure
( fourth revision)
ISO 3506-3 : 1997 IS 1367 ( Part 14/Sec 3 ) : 2002
Technical supply conditions for
threaded steel fasteners: Part 14
Mechanical properties of corrosion-
resistant stainless-steel fasteners,
Section 3 Set screws and similar
fasteners not under tensile stress
( third revision)
ISO 4042 : 1999 IS 1367 ( Part 11 ) : 2002 Technical
supply conditions for threaded steel
fasteners: Part 11 Electroplated
coatings ( third revision )
ISO 4753 : 1983 IS 1368 : 2003 Fasteners - Ends of
parts with external metric ISO thread
( fourth revision)
ISO 4759-1 : 2000 IS 1367 ( Part 2 ) : 2002 Technical
supply conditions for threaded steel
fasteners: Part 2 Tolerances for
fasteners - Bolts, screws, studs
and nuts - Product grades A, B
and C ( third revision)