IS 17017 : Part 31 : 2024 Electric Vehicle Conductive Charging System - Part 31 a.c. or d.c. Ev Supply Equipment for Where Protection Relies on Electrical Separation

ICS 43.120

ETD 51

1 SCOPE

1.1 This part of IS 17017 (Part 31), applies to electric road vehicle (EV) supply equipment for charging electric road vehicles, with a rated supply voltage up to 480 V a.c. or up to 600 V d.c. and a rated output voltage in case of a.c. not exceeding 240 V a.c. and output current not exceeding 32 A a.c. and in case of d.c. not exceeding 120 V d.c. and output current not exceeding 100 A d.c.

1.2 This standard provides the requirements for a.c. and/or d.c. EV supply equipment where the secondary circuit is protected from the primary circuit by electrical separation.

1.3 This standard also applies to EV supply equipment supplied from on-site storage systems (for example, buffer batteries and Inverter power supplies).

1.4 The aspects covered in this standard include:

 a) The characteristics and operating conditions of the EV supply equipment;

 b) The specification of the connection between the EV supply equipment and the EV; and

 c) The requirements for electrical safety EV supply equipment.

Additional requirements may apply to equipment designed for specific environments or conditions, for example:

 a) EV supply equipment located in hazardous areas where flammable gas or vapour and/or combustible materials, fuels or other combustible, or explosive materials are present;

 b) EV supply equipment designed to be installed at an altitude of more than 2 000 m; and

 c) EV supply equipment intended to be used on board on ships.

1.5 Requirements for electrical devices and components used in EV supply equipment are not included in this standard and are covered by their specific product standards.

1.6 Requirements for bi-directional power flow are not covered in this standard.

 a) Safety aspects related to maintenance;

 b) Charging of trolley buses, rail vehicles, industrial trucks and vehicles designed primarily for use off-road;

 c) Equipment on the EV;

 d) EMC requirements for equipment on the EV while connected, which are covered in IS 17017 (Part 21/Sec 1);

 e) Charging RESS off board of the EV; and

 f) Bi-directional energy transfer.

2 REFERENCES

The standards listed in Annex A contain provisions, which, through reference in this text, constitute provisions of this standard. At the time of publication, the editions indicated were valid. All standards are subject to revisions and parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent edition of these standards.

IS No/IEC No.

 Title

IS 732: 2019

 Code of practice for electrical wiring installations (fourth revision)

IS/IEC 60068-2-1 : 2007

 Environmental testing: Part 2 Test, Section Test A: cold

IS 9000 (Part 3/Sec 1 to 5) : 1977

 Basic environmental testing procedures for electronic and electrical items: Part 3 Dry heat test

IS 9000 (Part 4) : 2008/IEC 60068-2-78 : 2012

 Environmental Testing Part 4 Tests - Test Cab: Damp Heat, Steady State (Second Revision )

IS 9000 (Part 5/Sec 1 and 2) : 1981

 Basic environmental testing procedures for electronic and electrical items: Part 5 Damp heat (cyclic) test.

IS 13703 (all parts) Low voltage fuses

IS 15382 (Part 1) : 2014

 Insulation coordination for equipment within low-voltage Systems: Part 1 Principles, requirements, and tests (first revision)

ISO 15118-1 : 2013

 Road vehicles - Vehicle to grid communication interface - Part 1: General information and use-case definition

ISO 17409: 2015

 Electrically propelled road vehicles - Connection to an external electric power supply - Safety requirements

IS/IEC 60309-1 : 2002

 Plugs, socket-outlets and couplers for industrial purposes: Part 1 General requirements

IS/IEC 60309-2 : 2002

 Plugs, socket-outlets and couplers for industrial purposes: Part 2 Dimensional interchangeability requirements for pin and contact-tube accessories

IS 12640 (Part 1) : 2016/IEC 61008-1 :2012

 Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCBs): Part 1 General rules (second revision)

IS 12640 (Part 2) : 2016/IEC 61009 -1 : 2012

 Residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (RCBOs): Part 2 General rules (second revision)

IS/IEC 61439-1 : 2011

 Low-voltage switchgear and controlgear assemblies: Part 1 General rules (under print)

IEC TS 61439-7 : 2023

 Low-voltage switchgear and controlgear assemblies - Part 7: Assemblies for specific applications such as marinas, camping sites, market squares, electric vehicles charging stations (first revision)

IS/IEC 61508 (all parts)

 Functional safety of electrical/electronic/programma ble electronic safety related systems

IS 17017-24 : 2021

 Electric vehicle conductive charging system - Part 24: Digital communication between a d.c. electric vehicle supply equipment and an electric vehicle for control of d.c. charging

IEC 62335 : 2008

 Circuit breakers - Switched protective earth portable residual current devices for class I and battery powered vehicle applications

IS 17120 : 2019

 In-cable control and protection device for mode 2 charging of electric road vehicles (IC-CPD)

IS 17017 (Part 2/Sec 7) : 2023

 Electric vehicle conductive charging system: Plugs, socket - outlets, vehicle connectors and vehicle inlets, Section 7: Dimensional compatibility and interchangeability requirements for a.c., d.c. and a.c./d.c. pin and contact-tube vehicle couplers intended to be used for a.c./d.c. EV supply equipment where protection relies on electrical separation

IS 12360 : 1988

 Voltage bands for electrical installations including preferred voltages and frequency

IS 17017 (Part 23) : 2021

 Electric vehicle conductive charging system - Part 23: d.c. electric vehicle charging station

IS 13252 (Part 1) : 2010

 Information technology equipment - Safety: Part 1 General requirements (second revision)

IS/IEC 60529 : 2001

 Degrees of protection provided by enclosures (IP code)

IS/IEC 60898-1 : 2015

 Electrical accessories - Circuit-breakers for overcurrent protection for household and similar installations: Part 1 Circuit-breakers for a.c. operation (first revision)

IS/IEC 60898-2 : 2016

 Electrical accessories - Circuit-breakers for overcurrent protection for household and similar installations: Part 2 Circuit-breakers for a.c. and d.c. operation

IS/IEC 60947-2 : 2016

 Low-voltage switchgear and controlgear: Part 2 Circuitbreakers (first revision)

IS/IEC 60947-3 : 2012

 Low-voltage switchgear and controlgear: Part 3 Switches, disconnectors, switchdisconnectors and fusecombination units (first revision)

IS/IEC 60947-4-1 : 2012

 Low voltage switchgear and controlgear: Part 4 Contactors and motor-starters, Sec 1 Electromechanical contactors and motor-starters (first revision)

IS 17039 : 2018/IEC 61316 : 1999

 Industrial cable reels

IS/IEC 61558-1 : 1997

 Safety of power transformers, power supply units and similar: Part 1 General requirements and tests

IEC 61558-2-4 : 2009

 Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-4: Particular requirements and tests for isolating transformers and power supply units incorporating isolating transformers

IS/IEC 60947-6-2 : 2020

 Low-voltage switchgear and controlgear - Part 6-2: Multiple function equipment - Control and protective switching devices (or equipment) (CPS)

IS/IEC 60990 : 2016

 Methods of measurement of touch current and protective conductor current (first revision)

IEC 61180 : 2016

 High-voltage test techniques for low-voltage equipment - Definitions, test and procedure requirements, test equipment IS/IEC 61810 Electromechanical elementary relays: Part 1 General and safety requirements (under print)

IS 17050 : 2023/IEC 62262 : 2002+AMD1 : 2021

 Degrees of protection provided by enclosures for electrical equipment against external mechanical impacts (IK code)

IS 9409 : 2023 1980/IEC 61140 : 2016

 Classification of electrical and electronic equipment with regard to protection against electric shock

IS 10101 : 2019/ISO 3297 : 2017

 Information and documentation - International standard serial number (ISSN) (third revision)

IS 16826 : 2018/IEC 61180 : 2016

 High-voltage test techniques for low-voltage equipment - Definitions, test and procedure requirements, test equipment

IS/IEC 61439-7 : 2022

 Low-voltage switchgear and controlgear assemblies: Part 7 Assemblies for specific applications such as marinas, camping sites, market squares, electric vehicle charging stations

IEC 62477-1 : 2022

 Safety requirements for power electronic converter systems and equipment: Part 1 General

IEC 62893-4-1 : 2020

 Charging cables for electric vehicles of rated voltages up to and including 0.6/1 kV - Part 4-1: Cables for d.c. charging according to mode 4 of IEC61851-1 - d.c. charging without use of a thermal management system

ISO 11898-1 : 2015

 Road vehicles - Controller area network (CAN) - Part 1: Data link layer and physical signaling

ISO 11898-2 : 2016

 Road vehicles - Controller area network (CAN) - Part 2: High-speed medium access unit

IEC 62368-1 : 2018

 Audio/video, information and communication technology equipment - Part 1: Safety requirements