IS 302 : Part 2 : Sec 13 : 2024/IEC 60335-2-13 : 2021 Household and Similar Electrical Appliances - Safety - Part 2 Particular Requirements - Section 13 Deep Fat Fryers, Frying Pans and Similar Appliances

ICS 13.120; 97.040.50

ETD 32

NATIONAL FOREWORD

This Indian Standard (Part 2/Sec 13) (First Revision) which is identical to IEC 60335-2-13 : 2021 'Household and similar electrical appliances - Safety - Part 2-13: Particular requirements for deep fat fryers, frying pans and similar appliances' was adopted by the Bureau of Indian Standards on the recommendation of the Electrical Appliances Sectional Committee and approval of the Electrotechnical Division Council.

This standard was first published in 1994. This revision has been undertaken to harmonize with the latest version of IEC 60335-2-13.

This standard covers the safety requirements of deep fat fryers, frying pans and similar appliances. This standard does not cover the performance requirements, which are covered under a separate standard (refer IS 10436 'Specification for electric frying pans and deep fat fryers').

This Part 2 is to be used in conjunction with IS 302 (Part 1) : 2024 'Household and similar electrical appliances - Safety: Part 1 General requirements (seventh revision)'.

NOTE - When 'Part 1' is mentioned in this standard, it refers to IS 302 (Part 1).

This Part 2 supplements or modifies the corresponding clauses in IS 302 (Part 1), so as to convert that publication into the Indian Standard: Safety requirements for deep fat fryers, frying pans and similar appliances.

When a particular subclause of Part 1 is not mentioned in this standard, that subclause applies as far as is reasonable. When this standard states "addition", "modification" or "replacement", the relevant text in Part 1 is to be adapted accordingly.

NOTES

1 The following numbering system is used:

a) Subclauses, tables and figures that are numbered starting from 101 are additional to those in Part 1;

b) Unless notes are in a new subclause or involve notes in Part 1, they are numbered starting from 101, including those in a replaced clause or subclause; and

c) Additional annexes are lettered AA, BB, etc.

2 The following print types are used:

a) Requirements: in roman type;

b) Test specifications: in italic type; and

c) Notes: in small roman type.

Should however, any deviation exist between IS 302 (Part 1) : 2024 and this standard, the provisions of the latter shall apply.

This revision includes the following significant technical changes with respect to the previous version (minor changes are not listed):

a) Modification in recommended maximum quantity of oil for deep fat fryers (1);

b) Addition of normative references (2);

c) Modifications in marking and instructions (7);

d) An additional test has been introduced to limit the temperature rise of external accessible surfaces including marking of hot surfaces (7 and 11);

e) Modifications in temperature rise requirements (11.2, 11.3,11.8);

f) Introduction of a new 12 charging of metal-ion batteries;

g) Test for transient over voltages added (14);

h) Modification in test for moisture resistance (15.101);

j) Modifications in tests for abnormal operation (19);

k) Modification in construction requirements (22.12, 22.35, 22.101);

m) Modification in requirements for appliance couplers incorporating thermostats, thermal cutouts or fuses in the connector (24.1.5);

n) Addition of pollution degree 3 microenvironment unless the insulation is enclosed or located (29.2);

p) Test for glow wire and needle flame test added (30);

q) Test for electromagnetic compatibility (EMC) added;

r) Annex on battery-operated appliances, separable batteries and detachable batteries for battery-operated appliances added; and

s) Figure of probe for measuring surface temperatures added.

The text of IEC standard has been approved as suitable for publication as an Indian Standard without deviations. Certain terminologies and conventions are, however, not identical to those used in Indian Standards. Attention is particularly drawn to the following:

a) Wherever the words 'International Standard' appear referring to this standard, they should be read as 'Indian Standard'; and

b) Comma (,) has been used as a decimal marker, while in Indian Standards the current practice is to use a point (.) as the decimal marker.